PSC PT Program Generator Especificaciones Pagina 101
- Pagina / 122
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Programming Parameters
Product Reference Guide E-7
Xmodem Protocol
The PT40 supports the Xmodem (checksum) file-transfer protocol for serial
communication, which is available in many commercially marketed products.
Xmodem is a simple send-and-wait-for-response protocol using a fixed-length
data field. The data field is embedded in an Xmodem packet, which also con-
tains a packet number and a single-byte arithmetic checksum. The protocol
link is established by the receiver transmitting a NAK character until the
sender responds. The sender responds by transmitting an Xmodem packet.
The sender then waits for either an ACK signal, in which case it transmits the
next packet, or a NAK signal, in which case it retransmits the packet. Once all
packets are transmitted, the sender transmits an EOT signal, indicating the
end of transmission.
Scan the following bar code to set a PT40 to use the Xmodem protocol:
Save-and-Exit Settings
Table E-4. Save-and-Exit Settings
Xmodem protocol
*$+$-CA02EE*
Setting ID # Type
Save and exit EE Immediate
Exit only, no save EF Immediate
2340.book Page 7 Wednesday, January 29, 2003 12:50 PM
- Product Reference Guide 1
- Table of Contents 3
- iii 5
- About this Guide 7
- Registering Your Falcon PT40 8
- Document Conventions 9
- PT40 Labels 10
- Chapter 1 11
- Introduction 11
- PT40 Power Button and Reset 12
- The Keypad 13
- Data Keys 14
- Function Keys 15
- Action Keys 16
- The Display Screen 17
- The PT40 Laser 18
- The Beeper 19
- PT40 Software Applications 20
- Application and Data Flow 21
- Accessories 22
- PT40 Belt Clip 23
- PT40 Soft Case 24
- Falcon PT40 Product CD 24
- Chapter 2 25
- Data Collection with PT40 25
- Software Applications 25
- Quick Start 26
- Setting Up the PT40 27
- Switching Applications 28
- Setting the Time and Date 29
- Setting a Password 30
- Installing PALPRO40 31
- Using PALPRO40 31
- 2-8 Falcon 32
- 2-10 Falcon 34
- Using ASSETPRO 34
- 2-12 Falcon 36
- Using INVPRO 36
- Using Two Prompts 37
- 2-14 Falcon 38
- Using TRACKPRO 39
- 2-16 Falcon 40
- DESCRIPT 42
- 2-20 Falcon 44
- Using DESCRIPT 45
- 2-22 Falcon 46
- INVMODEM 47
- 2-24 Falcon 48
- TIMESTMP 49
- 2-26 Falcon 50
- Reviewing the Collected Data 51
- 2-28 Falcon 52
- Chapter 3 53
- Transferring Files and Data 53
- Uploading Data to the Host PC 54
- Using XFER32 54
- XFER32 Setup 55
- 3-4 Falcon 56
- Transfer Tab 57
- 3-6 Falcon 58
- Logging Tab 58
- Transmit Files 59
- Receive Files 59
- 3-8 Falcon 60
- Product Reference Guide 3-9 61
- 3-10 Falcon 62
- 3-12 Falcon 64
- 3-14 Falcon 66
- Appendix A 67
- Falcon PT40 Batteries 67
- A-2 Falcon 68
- Main Battery Installation 69
- Recharging the Batteries 70
- Product Reference Guide A-5 71
- Figure A-5 on page A-6: 71
- Figure A-5 on page A-6 71
- A-6 Falcon 72
- Storing the Main Battery 73
- Backup Battery 73
- Low Battery Indication 73
- PT40 Dock, Serial Cable 75
- Appendix B 75
- Serial Cable 76
- Power Adaptor 76
- Attaching the PT40 to a PC 77
- B-4 Falcon 78
- Appendix C 79
- Connector Configurations 79
- PT40 Dock 80
- Appendix D 81
- Configuring with Bar Codes 81
- D-2 Falcon 82
- Interleaved 2 of 5 83
- D-4 Falcon 84
- Product Reference Guide D-5 85
- D-6 Falcon 86
- Product Reference Guide D-7 87
- UPC/EAN/JAN Extensions 88
- Code 128 88
- Other Controls 89
- D-10 Falcon 90
- Product Reference Guide D-11 91
- (in seconds) 91
- Clock and Calendar 92
- DATA BITS 93
- STOP BITS 93
- ENABLE XON/OFF 93
- LINEFEED 93
- D-14 Falcon 94
- Appendix E 95
- E-2 Falcon 96
- *$+$-C8EE* 97
- E-4 Falcon 98
- *$+$-0010235EE* 99
- *$+$-001* *0235EE* 99
- Programming Parameters 100
- *$+$-CA02EE* 101
- E-8 Falcon 102
- Product Reference Guide E-9 103
- E-10 Falcon 104
- Product Reference Guide E-11 105
- Serial Parameters 106
- Product Reference Guide E-13 107
- E-14 Falcon 108
- Appendix F 109
- Memory Table 109
- F-2 Falcon 110
- Appendix G 111
- Maintenance 111
- Troubleshooting, and 111
- Technical Support 111
- Troubleshooting 112
- Product Reference Guide G-3 113
- xi 117
- xiii 119
Relacionado con productos y manuales para Generadores De Poder PSC PT Program Generator
(204 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales