Psc Handheld Laser Bar Code Scanners Keyboard Wedge / Manual de usuario descargar pdf (Pagina 14)

6 User’s / Programming Guide

NO Enable AutoSense

NN Disable AutoSense

To use this mode of operation properly, the user must first attach the

plastic scanner holder to the bracket of the stand as shown in

Figure 1. The (NO) Enable AutoSense

programming symbol is

scanned until the green “Good Decode” light blinks. This will acti-

vate the trigger screen. The scanner is then placed into the holder and

the user must check that the red laser beam is aimed at the reflective

label affixed to the stand. The AutoSense

is now ready to read labels

presented to it.

Figure 1. The PSC AutoSense

Stand

a. Riser sub-assembly d. Reflective tape

b. Scanner holder e. Stand base

c. Scanner

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 87 88

User’s / Programming Guide 1
Disclaimer 2
Table of Contents 5
06656 iii 7
Introduction 9
Unpacking 10
Installation 10
3 11
4 User’s / Programming Guide 12
Serial Communications 12
5 13
AutoSense 13
Operation 13
6 User’s / Programming Guide 14
7 15
Wand Emulation Operation 15
Setup Overview 16
9 17
10 User’s / Programming Guide 18
11 19
12 User’s / Programming Guide 20
13 21
Serial Communication 21
14 User’s / Programming Guide 22
15 23
16 User’s / Programming Guide 24
17 25
18 User’s / Programming Guide 26
19 27
20 User’s / Programming Guide 28
General Parameters 29
22 User’s / Programming Guide 30
23 31
24 User’s / Programming Guide 32
Message Formatting 33
26 User’s / Programming Guide 34
27 35
28 User’s / Programming Guide 36
29 37
30 User’s / Programming Guide 38
Serial Commands 39
32 User’s / Programming Guide 40
33 41
Keyboard Wedge Parameters 42
35 43
36 User’s / Programming Guide 44
37 45
Symbologies 46
39 47
40 User’s / Programming Guide 48
41 49
42 User’s / Programming Guide 50
43 51
44 User’s / Programming Guide 52
45 53
46 User’s / Programming Guide 54
Code 2 of 5 – Interleaved 54
47 55
Code 2 of 5 – Standard 55
48 User’s / Programming Guide 56
Code 128 56
49 57
50 User’s / Programming Guide 58
MSI/Plessey 58
51 59
52 User’s / Programming Guide 60
53 61
Digit Selection 61
54 User’s / Programming Guide 62
Symbology Identifiers 62
55 63
56 User’s / Programming Guide 64
57 65
Wand Emulation Parameters 66
59 67
60 User’s / Programming Guide 68
Data Synchronization 68
61 69
Memory Module 70
63 71
Marker Beam 72
65 73
Scanner Labeling 74
67 75
Maintenance 75
Cleaning 75
Inspection 75
Technical Support 76
Appendix A 77
70 User’s / Programming Guide 78
71 79
72 User’s / Programming Guide 80
73 81
74 User’s / Programming Guide 82
75 83
76 User’s / Programming Guide 84
77 85
78 User’s / Programming Guide 86

Comentarios a estos manuales

Sin comentarios

Psc Handheld Laser Bar Code Scanners Keyboard Wedge / Manual de usuario Pagina 14

Comentarios a estos manuales

Relacionado con productos y manuales para Escáneres Psc Handheld Laser Bar Code Scanners Keyboard Wedge /