PSC SP400rf Manual de usuario Pagina 32
- Pagina / 112
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
26
SP400RF
Programming Guide
K
EYBOARD
W
EDGE
INTERFACE
STI KEYBOARD WEDGE INTERFACE SELECTION
Scan this label to enable the STI Keyboard Wedge interface.
IMPORTANT
When enabling the STI Keyboard Wedge interface, certain parameters
must be set to ensure proper communication with the wedge. Reference
the tables below for these requirements. When all required parameters
have been set for the interface, the entire set of STI Keyboard Wedge
programmable features can be accessed using either the Master
®
BB+
Universal Programming Guide or the VS/HS Keyboard Wedge Program-
ming Guide (P/N R44-1343) available through your dealer.
Section of this Manual
RS-232 I/F Label Transmit
Format Config
General Features Code 39 Symbology
Baud = 9600 Pref ix = None STX = None Symbology = Enable
Parity = Even Suffix = Carriage
Return (0xOD)
ETX = None Check Digit Calc =
Don’ t Calculate
Stop Bits = 1 Label ID = None
(except IBMXXXX.
See below)
ACK /NAK for
Labels = Disable
Check Digit = Don’ t
Send
Data Bits = Seven ACK /NAK for
Commands =
Disable
Start/Stop Character =
Don’ t Send
Hardware Control
= None
Label ON/OFF File
= Disable
Read One Char Label
= Disable
Xon/Xof f =Disable C39 Min Length = 1
C39 Full ASCI I =
Disable
IBMXXXX STI WEDGE
The IBMXXXX STI Wedge has the exception that the Label ID must be
enabled as a Prefix using the standard default value for the symbology to
be used
- REQUENCY 1
- PSC Scanning, Inc 2
- Contents 3
- Symbologies 4
- Appendix A 5
- Appendix B 5
- Appendix C 5
- INTRODUCTION 7
- CHANGING INTERFACES 8
- INFORMATION 9
- PROGRAMMING OVERVIEW 10
- THE PROGRAMMING SESSION 11
- IF YOU MAKE A MISTAKE 12
- RETURN TO FACTORY SETTINGS 12
- CONFIGURATION UPLOAD 12
- WHERE TO GO FROM HERE 13
- ORT 5B INTERFACE SELECTION 14
- ORT 9A, 9B, 9C, 9E SETTINGS 15
- ORT E INTERFACE SELECTION 16
- OCIA INTERFACE SELECTION 17
- SNI OCIA INTERFACE SELECTION 17
- OCIA OPTIONS 18
- R44-1027 13 19
- WAND EMULATION 19
- INTERFACE 19
- MULATION 20
- NTERFACE 20
- RS-232 INTERFACE SELECTION 21
- AUD RATE 22
- R44-1027 17 23
- HARDWARE CONTROL 24
- SOFTWARE CONTROL 25
- MILLISECONDS 27
- NTERCHARACTER 27
- I/F Type PCs Supported 28
- R44-1027 25 31
- IMPORTANT 32
- IBMXXXX STI WEDGE 32
- PREFIX & SUFFIX 33
- ABEL TRANSMIT 35
- ORMAT CONFIG 35
- ET SUFFIX 36
- NE CHARACTER ONLY 38
- ASCII CHARACTER SET 39
- ONTINUED 41
- R44-1027 37 43
- R44-1027 39 45
- SYMBOLOGIES 47
- SYMBOLOGY OPTIONS OVERVIEW 48
- SYMBOLOGY SELECTION 49
- UPC/EAN OPTIONS 51
- UPC/EAN EXPANSION 52
- UPC/EAN ADD-ONS 53
- END CHECK DIGIT 55
- PRICE/WEIGHT CHECK DIGIT 56
- CODE 39 OPTIONS 57
- CODE 39 (CONTINUED) 58
- ODE 39 MINIMUM 60
- ABEL LENGTH 60
- INTERLEAVED 2 OF 5 61
- YMBOLOGY 62
- ELECTION 62
- ET FIXED 63
- ETTING FIXED LENGTHS 63
- ETTING MINIMUM LABEL LENGTH 63
- R44-1027 59 65
- STANDARD 2 OF 5 66
- ORMAL STANDARD 2 OF 5 67
- TANDARD 2 OF 5 67
- ET FIRST FIXED LENGTH 69
- CODABAR OPTIONS 71
- Start/Stop 73
- Standard Factory Settings 73
- CODABAR FIXED LENGTH 74
- R44-1027 69 75
- MSI/PLESSEY CHECK DIGIT 76
- NABLE MSI/PLESSEY FIXED 77
- ISABLE MSI/PLESSEY FIXED 77
- NABLE FIXED L 77
- ET SECOND FIXED LENGTH 78
- O SECOND FIXED LENGTH 78
- LESSEY SET FIXED 78
- NABLE 79
- YMBOLOGY ID PREFIX 79
- GENERAL FEATURES 80
- COMMUNICATIONS PROTOCOL 81
- FEATURES 83
- ET STX 85
- ET ETX 85
- ET STX/ETX 85
- "When to Beep" 86
- CTS enabled 88
- R44-1027 83 89
- “WHEN TO BEEP” OPTIONS 90
- R44-1027 87 93
- BEEPER VOLUME 94
- RADIO CHANNEL FREQUENCY 95
- Radio Channel Frequency 96
- AIT TIME FOR HOST ACKNOWLEDGE 97
- IME FOR HOST 98
- CKNOWLEDGE 98
- READ VERIFICATION 99
- Programming Guide 100
- LOW BATTERY INDICATION METHOD 101
- APPENDIX A 102
- STANDARD FACTORY SETTINGS 102
- TANDARD 2 OF 5 103
- ISC. GENERAL FEATURES 104
- EAD VERIFICATION 104
- TEM ON/OFF FILE 104
- UDIBLE INDICATOR SETTINGS 104
- INTERFACE-DISCRETE DEFAULTS 105
- IBM INTERFACES 106
- APPENDIX B 107
- ADDITIONAL INFORMATION 107
- APPENDIX C 108
- SAMPLE BARCODES 108
- 1 101234 567891 109
- LANK PAGE 111
- Corporate Headquarters 112
Relacionado con productos y manuales para Lectores De Códigos De Barras PSC SP400rf
(104 paginas)
(48 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.072 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales